Форум ребризер-дайверов
http://rebreather.org.ua/

Как цеплять компы к датчикам?
http://rebreather.org.ua/viewtopic.php?f=22&t=602
Страница 1 из 1

Автор:  Snusmumrik [ 20 сен 2010, 16:01 ]
Заголовок сообщения:  Re: Как цеплять компы к датчикам?

Перерезать резьбу на любой гермоввод IP68 (к примеру, на M12x1,5) и через него ввести кабель от компа.

Автор:  Fliper [ 20 сен 2010, 16:49 ]
Заголовок сообщения:  Re: Как цеплять компы к датчикам?

Cyclone писал(а):
Лёша, можно подробнее? Что за гермоввод? Где купить и как выглядит?

хоть и не Лёша, но отвечу:
http://www.avselectro.ru/catalog/000z67 ... 4lvor.html
http://www.korpus-center.ru/default.aspx?catalog=2125

Автор:  Snusmumrik [ 20 сен 2010, 16:54 ]
Заголовок сообщения:  Re: Как цеплять компы к датчикам?

http://www.chipdip.ru/catalog/show/plastic-cable-glands.aspx?mode=parm&gmnf=&p.1578=%CA%E0%E1%E5%EB%FC%ED%FB%E9+%E2%E2%EE%E4&p.1579=&sklad=

Автор:  Fliper [ 20 сен 2010, 17:03 ]
Заголовок сообщения:  Re: ида-71 mccr от Томановского

Cyclone писал(а):
Очень хочется увидеть, каким образом подключен к датчику VR3

http://narkedat90.com/shop/content/cable_help/
Цитата:
Cable and Connector Help



VR3 CONNECTIONS (1 CELL)

WARNING - VR3 CABLES REQUIRE A DISCRETE COMPONENT IN THE CONNECTOR TO WORK CORRECTLY. DO NOT ATTEMPT TO MAKE YOUR OWN VR3 CABLE UNLESS YOU FIT THIS COMPONENT.

Below is a close up view of the pins inside the connector. Take note of the crescent shape in the connector which is to locate the connector in the correct orientation and helps you with pin identification
Вложение:
VR3PINOUTS.jpg
VR3PINOUTS.jpg [ 26.63 КБ | Просмотров: 40504 ]



Below is the cable cores after the outer shielding is stripped off

there is 4 cores BUT ONLY 2 ARE USED FOR THE VR3


THIS IS FOR THE BELDON CABLE ONLY


1 WHITE that is connected to pin# 3 in the connector and is POSITIVE

2 BLUE that is connected to pin# 1 in the connector and is NEGATIVE

3 WHITE/blue this conductor is not used for the VR3

4 BLUE/white this conductor is not used for the VR3
Вложение:
VR3CABLECONNECTIONS.jpg
VR3CABLECONNECTIONS.jpg [ 97.39 КБ | Просмотров: 40504 ]



-------------------------------------------------------------------------------
SHEARWATER CONNECTIONS (3 CELL)

Below is a close up view of the pins inside the connector, take note of the crescent shape in the connector is is to locate the connector in the correct orientation and helps you with pin identification
Вложение:
SHEARWATERPINOUTS.jpg
SHEARWATERPINOUTS.jpg [ 30.28 КБ | Просмотров: 40504 ]


Below is the cable cores after the outer shielding is stripped off

there are 4 cores all of which are used

WHITE/BLUE (PIN2) CELL1

WHITE (PIN 3) CELL 2

BLUE/WHITE (PIN 4) CELL 3

BLUE (PIN 1) GROUND
Вложение:
SHEARWATERCABLECONNECTIONS.jpg
SHEARWATERCABLECONNECTIONS.jpg [ 26.36 КБ | Просмотров: 40504 ]



-------------------------------------------------------------------------------


Below is a R22 o2 cell note the orientation of the positive and negative cell pins
Вложение:
CELLWITHMOLEXCONNECTOR.jpg
CELLWITHMOLEXCONNECTOR.jpg [ 16.5 КБ | Просмотров: 40504 ]




Below is the newer R22D-AP cell fitted with the SMB connector.

This cell is used in APD's vision and evolution rebreathers as well as our DEEP PURSUIT™ and has a much superior connector

the center of the connector is POSITIVE

and the out part is NEGATIVE


Вложение:
CELLFITTEDWITHSMBCONNECTOR.jpg
CELLFITTEDWITHSMBCONNECTOR.jpg [ 31.07 КБ | Просмотров: 40504 ]

-------------------------------------------------------------------------------

We now use a very tough water stopped cable
It has 9 cores but we only use 4 cores for cable assemblys,
The cores we use are
Common: BLACK
Cell 1: RED
Cell2: BROWN
Cell3: PURPLE
The other cores are not used
Вложение:
water_stopped_cable_striped_back.jpg
water_stopped_cable_striped_back.jpg [ 19.98 КБ | Просмотров: 40504 ]


Автор:  chrondar [ 08 июн 2020, 20:02 ]
Заголовок сообщения:  Re: Как цеплять компы к датчикам?

Камрады, а никто не пользовал такой вот разъем (7 pin) с AliExpress? https://aliexpress.ru/item/32877103117. ... web201603_
Утверждают, что водонепроницаемый, IP68 :Botan:
Вложение:
222.jpg
222.jpg [ 404.34 КБ | Просмотров: 28518 ]


ПС: там еще и ответная часть есть...

Автор:  Alexx [ 09 июн 2020, 20:02 ]
Заголовок сообщения:  Re: Как цеплять компы к датчикам?

Именно такой разъем стоит на VR3 (в простонародье "карбюратор") :) IP68, не сомневайся.

Автор:  chrondar [ 09 июн 2020, 21:26 ]
Заголовок сообщения:  Re: Как цеплять компы к датчикам?

Balik68 писал(а):
Именно такой разъем стоит на VR3 (в простонародье "карбюратор") :) IP68, не сомневайся.

Понял. Спасибо, Саша! :friends:

Страница 1 из 1 Часовой пояс: UTC + 3 часа
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/